오토윈스 제품군
   Converter
   Arrester
   Graphic Driver
   Slim Converter
   Transmitter
   Indicator
 기상관측시스템
   기상센서
   자동기상관측시스템
 ICP-DAS 제품군
   I-7000 SERIES
   M-7000 SERIES
   I-7188 SERIES
   I-7500 SERIES
   Multi-port Serial Boards
   
  CAN to Ethernet Gateway
   




I-7540D

A/S,구입,기술문의 : 02) 2616-0533

 


DATA SHEET
 

I-7540D Data Sheet.pdf


  제품설명 고객문의 다운로드

Internet communications using TCP/IP is increasing in the industrial sector. Using Ethernet for network in industrial area is appealing because the required cabling is already installed. The CAN-Ethernet Gateway from ICP DAS is a solution that enables CAN networks to be coupled together over the Internet/Ethernet, whereby remote monitoring and control is possible. The CAN-Ethernet Gateway controls networked communication and makes a transparent CAN-based application interface available to the user.

The device supports a transparent, protocol-independent transfer of the CAN messages, thus allowing its implementation into a wide range of possible applications. Furthermore, the CAN-Ethernet Gateway can be used with various higher layer CAN protocols (e.g. CANopen, DeviceNet or other proprietary protocols). The following figure shows the application architecture for CAN-Ethernet Gateway .

Furthermore, I-7540D also can be used as Ethernet to CAN/RS-232/485 Device Server. The Device Server is an appliance that network enables any device with a serial communication port. By virtue of its independent operating system, protocol independence, small size and flexibility, Device servers are able to meet the demand of virtually any network-enable application. Most devices don't have network ports. I-7540D allows those devices to become connected to the network.

 


  • 80186-80 Embedded CPU, or compatible
  • Ethernet Protocols, TCP,UDP,IP,ICMP,ARP
  • 10/100 Base-TX Ethernet Controller
  • Reloadable Operating Software
  • Message transmitted by using TCP/IP protocol
  • Diagnostics
  • COM driver support interrupt & 1K QUEUE Input & Output buffer
  • Support one RS-232 port, one RS-485 port and one CAN port
  • 2500Vrms photo-isolation protection on CAN side.
  • Jumper select 120Ω terminator resistor for CAN channel
  • Phillip 82C 250/251CAN Transceiver
  • Support both CAN specification 2.0A and 2.0B.
  • Max transmission speed up to 1M bps for CAN and 115.2K bps for RS-232 & RS-485
  • Max transmission distance of CAN over 1000m (follow CAN specification)
  • Built-in self-tuner ASIC controller on RS-485 port
  • 7-segment LED display.
  • Software configurable CAN and RS-232 communication parameters
  • Firmware updated from COM1 or Ethernet port
  • Support Web Configuration
  • Support max 25 Ethernet clients connection
  • Support for Virtual COM technology
  • CPU
    CPU
    80186, 80MHz or compatible
    SRAM
    512K Bytes
    Flash
    512K Bytes
    EEPROM
    16K Bytes
    NVRAM
    31 Bytes (battery backup, data valid up to 10 year)
    RTC (Real Time Clock)
    Yes
    64-bit Hardware Serial Number
    Yes
    Built-in Watchdog Timer
    Yes
    Communication Interface
    COM1
    RS-232 (TXD, RXD, RTS, CTS, GND)
    COM2
    RS-485 (D2+, D2-)
    CAN
    One CAN port with two CAN bus connector interfaces (CAN_H, CAN_L)
    Ethernet Port
    10/100Base-TX Ethernet Controller
    (Auto-negotiating, Auto_MDIX, LED indicator)
    COM Port Formats
    Data bit
    7, 8
    Parity
    Even, Odd, None
    Stop bit
    1
    Baud-rate
    115.2Kbps max.
    CAN Port Formats
    CAN Controller
    Phillips SJA1000T CAN Controller
    CAN Transceiver
    Phillips 82C250 CAN Transceiver
    Isolated
    2500Vrms on CAN side
    Baud-rate
    1Mbps max.
    Dimensions
    I-7540D
    122 x 72 x 33 mm
    Operating Environment
    Operating Temperature
    -25°C to +75°C
    Storage Temperature
    -40°C to +80°C
    Power
    Protection
    Power reverse polarity protection
    Frame Ground for ESD Protection
    Yes
    Required Supply Voltage
    +10 to +30VDC (non-regulated)
    Power consumption
    2.5W

    I-7540D
    Internet communication controller with one CAN bus, one RS-232, one RS-485 and one Ethernet